ComSkip.Ini for german "premiere world"

To discuss the tuning of comskip and for posting your ini files
Post Reply
sascha
Posts: 17
Joined: Sun May 28, 2006 8:16 pm

ComSkip.Ini for german "premiere world"

Post by sascha » Fri Jun 02, 2006 11:38 pm

The .ini is tuned for german "premiere world" channel "film 1-7", disney and jetix, don't tested on other subchannels.

Film channels do not have any logo and no commercial in the films.

Sascha

Code: Select all

detect_method=43			;1=black frame, 2=logo, 4=scene change, 8=fuzzy logic, 16=closed captions, 32=aspect ration, 64=silence, 255=all
verbose=0				;show a lot of extra info, level 5 is also OK, set to 0 to disable
max_brightness=150      			;frame not black if any pixels checked are greater than this (scale 0 to 255)
test_brightness=150      		;frame not pure black if any pixels checked are greater than this, will check average brightness (scale 0 to 255)
max_avg_brightness=20			;lower than 15 for StarTrek ;maximum average brightness for a dim frame to be considered black (scale 0 to 255) 0 means autosetting
max_commercialbreak=600 		;maximum length in seconds to consider a segment a commercial break
min_commercialbreak=40			;minimum length in seconds to consider a segment a commercial break
max_commercial_size=160			;maximum time in seconds for a single commercial or multiple commercials if no breaks in between
min_commercial_size=20   		;mimimum time in seconds for a single commercial
min_show_segment_length=300 		; any segment longer than this will be scored towards show.
non_uniformity=500
max_volume=100				; any frame with sound volume larger than this will not be regarded as black frame
min_silence=10				; Any deep silence longer than this amount  of frames is a possible cutpoint
ticker_tape=0				; Amount of pixels from bottom to ignore in all processing 
max_repair_size=200

;### Punsih ###

punish=1					; Compare to average for sum of 1=brightness, 2=uniform 4=volume, 8=silence, 16=schange, set to 0 to disable
punish_threshold=1.3			; Multiply when amount is above average * punish_threshold
punish_modifier=2.0			; When above average * threshold multiply score by this value


length_strict_modifier=1.1
length_nonstrict_modifier=1.5 
combined_length_strict_modifier=2.0
combined_length_nonstrict_modifier=1.25
logo_present_modifier=0.01
excessive_length_modifier=0.01
ar_wrong_modifier=1.0
min_schange_modifier=0.5
max_schange_modifier=2.0
schange_threshold=80
cc_commercial_type_modifier=4.0
cc_wrong_type_modifier=2.1
cc_correct_type_modifier=0.75
dictionary_modifier=1.00


intelligent_brightness=0 		; Set to 1 to use a USA specific algorithm to tune some of the settings, not adviced outside the USA
give_up_logo_search=2000 


;### Logo ###

logo_percentile=0.92			; if more then this amount of logo is found then logo detection will be disabled
logo_threshold=0.50
aggressive_logo_rejection=0
connect_blocks_with_logo=1		; set to 1 if you want successive blocks with logo on the transition to be regarded as connected, set to 0 to disable
cut_on_ar_change=1			; set to 1 if you want to cut also on aspect ratio changes, set to 0 to disable
delete_show_after_last_commercial=1	; set to 1 if you want to delete the last block if its a show and after a commercial
delete_show_before_first_commercial=1
delete_show_before_or_after_current=1	; set to 1 if you want to delete the previous and the next show in the recording, this can lead to the deletion of trailers of next show
shrink_logo=15				; Reduce the duration of the logo with this amount of seconds
after_logo=0		; set to number of seconds after logo disappears comskip should start to search for silence to insert an additional cutpoint
before_logo=0 ;
reward=0
padding=0
ms_audio_delay=5
logo_max_percentage_of_screen=0.35
subtitles=0
delete_logo_file=1			; set to 1 if you want comskip to tidy up after finishing


;### Output ###

output_framearray=0			; create a big excel file for detailed analysis, set to 0 to disable
output_videoredo=0
output_womble=0
output_cuttermaran=0
output_mpeg2schnitt=0
output_mpgtx=0
output_zoomplayer_chapter=0
output_zoomplayer_cutlist=0
output_edl=0
output_vcf=0
output_btv=0				; set to 1 if you want Beyond TV chapter cutlist output
output_projectx=0			; set to 1 if you want ProjectX cutlist output (Xcl)
output_demux=0				; set to 1 if you want comskip to demux the mpeg file while scanning

live_tv=0					; set to 1 if you use parallelprocessing and need the output while recording
dictionary=0
cuttermaran_options="cut=\"true\" unattended=\"true\" muxResult=\"false\" snapToCutPoints=\"true\" closeApp=\"true\""
mpeg2schnitt_options="mpeg2schnitt.exe /S /E /R25  /Z %2 %1"


Post Reply