ComSkip.Ini for german "premiere world"
Posted: Fri Jun 02, 2006 11:38 pm
The .ini is tuned for german "premiere world" channel "film 1-7", disney and jetix, don't tested on other subchannels.
Film channels do not have any logo and no commercial in the films.
Sascha
Film channels do not have any logo and no commercial in the films.
Sascha
Code: Select all
detect_method=43 ;1=black frame, 2=logo, 4=scene change, 8=fuzzy logic, 16=closed captions, 32=aspect ration, 64=silence, 255=all
verbose=0 ;show a lot of extra info, level 5 is also OK, set to 0 to disable
max_brightness=150 ;frame not black if any pixels checked are greater than this (scale 0 to 255)
test_brightness=150 ;frame not pure black if any pixels checked are greater than this, will check average brightness (scale 0 to 255)
max_avg_brightness=20 ;lower than 15 for StarTrek ;maximum average brightness for a dim frame to be considered black (scale 0 to 255) 0 means autosetting
max_commercialbreak=600 ;maximum length in seconds to consider a segment a commercial break
min_commercialbreak=40 ;minimum length in seconds to consider a segment a commercial break
max_commercial_size=160 ;maximum time in seconds for a single commercial or multiple commercials if no breaks in between
min_commercial_size=20 ;mimimum time in seconds for a single commercial
min_show_segment_length=300 ; any segment longer than this will be scored towards show.
non_uniformity=500
max_volume=100 ; any frame with sound volume larger than this will not be regarded as black frame
min_silence=10 ; Any deep silence longer than this amount of frames is a possible cutpoint
ticker_tape=0 ; Amount of pixels from bottom to ignore in all processing
max_repair_size=200
;### Punsih ###
punish=1 ; Compare to average for sum of 1=brightness, 2=uniform 4=volume, 8=silence, 16=schange, set to 0 to disable
punish_threshold=1.3 ; Multiply when amount is above average * punish_threshold
punish_modifier=2.0 ; When above average * threshold multiply score by this value
length_strict_modifier=1.1
length_nonstrict_modifier=1.5
combined_length_strict_modifier=2.0
combined_length_nonstrict_modifier=1.25
logo_present_modifier=0.01
excessive_length_modifier=0.01
ar_wrong_modifier=1.0
min_schange_modifier=0.5
max_schange_modifier=2.0
schange_threshold=80
cc_commercial_type_modifier=4.0
cc_wrong_type_modifier=2.1
cc_correct_type_modifier=0.75
dictionary_modifier=1.00
intelligent_brightness=0 ; Set to 1 to use a USA specific algorithm to tune some of the settings, not adviced outside the USA
give_up_logo_search=2000
;### Logo ###
logo_percentile=0.92 ; if more then this amount of logo is found then logo detection will be disabled
logo_threshold=0.50
aggressive_logo_rejection=0
connect_blocks_with_logo=1 ; set to 1 if you want successive blocks with logo on the transition to be regarded as connected, set to 0 to disable
cut_on_ar_change=1 ; set to 1 if you want to cut also on aspect ratio changes, set to 0 to disable
delete_show_after_last_commercial=1 ; set to 1 if you want to delete the last block if its a show and after a commercial
delete_show_before_first_commercial=1
delete_show_before_or_after_current=1 ; set to 1 if you want to delete the previous and the next show in the recording, this can lead to the deletion of trailers of next show
shrink_logo=15 ; Reduce the duration of the logo with this amount of seconds
after_logo=0 ; set to number of seconds after logo disappears comskip should start to search for silence to insert an additional cutpoint
before_logo=0 ;
reward=0
padding=0
ms_audio_delay=5
logo_max_percentage_of_screen=0.35
subtitles=0
delete_logo_file=1 ; set to 1 if you want comskip to tidy up after finishing
;### Output ###
output_framearray=0 ; create a big excel file for detailed analysis, set to 0 to disable
output_videoredo=0
output_womble=0
output_cuttermaran=0
output_mpeg2schnitt=0
output_mpgtx=0
output_zoomplayer_chapter=0
output_zoomplayer_cutlist=0
output_edl=0
output_vcf=0
output_btv=0 ; set to 1 if you want Beyond TV chapter cutlist output
output_projectx=0 ; set to 1 if you want ProjectX cutlist output (Xcl)
output_demux=0 ; set to 1 if you want comskip to demux the mpeg file while scanning
live_tv=0 ; set to 1 if you use parallelprocessing and need the output while recording
dictionary=0
cuttermaran_options="cut=\"true\" unattended=\"true\" muxResult=\"false\" snapToCutPoints=\"true\" closeApp=\"true\""
mpeg2schnitt_options="mpeg2schnitt.exe /S /E /R25 /Z %2 %1"