Comskip Support Forum

Comskip is a free commercial detector, browse the forum for more information
It is currently Wed Aug 21, 2019 3:21 pm

All times are UTC [ DST ]




Post new topic Reply to topic  [ 1 post ] 
Author Message
PostPosted: Sat Oct 07, 2006 2:58 pm 
Offline

Joined: Fri Sep 29, 2006 10:27 am
Posts: 12
Hi

This is an ini file of this forum improved of erik.

Every German channel works very fine up to "Das Vierte" there are always 5 seconds trailers, i can live with it. :lol:

Quote:
detect_method=43 ;1=black frame, 2=logo, 4=scene change, 8=fuzzy logic, 16=closed captions, 32=aspect ration, 64=silence, 255=all
verbose=10 ;show a lot of extra info, level 5 is also OK, set to 0 to disable
max_brightness=150 ;frame not black if any pixels checked are greater than this (scale 0 to 255)
test_brightness=150 ;frame not pure black if any pixels checked are greater than this, will check average brightness (scale 0 to 255)
max_avg_brightness=20 ;lower than 15 for StarTrek ;maximum average brightness for a dim frame to be considered black (scale 0 to 255) 0 means autosetting
max_commercialbreak=600 ;maximum length in seconds to consider a segment a commercial break
min_commercialbreak=40 ;minimum length in seconds to consider a segment a commercial break
max_commercial_size=160 ;maximum time in seconds for a single commercial or multiple commercials if no breaks in between
min_commercial_size=20 ;mimimum time in seconds for a single commercial
min_show_segment_length=100 ; any segment longer than this will be scored towards show.
non_uniformity=1000
max_volume=100 ; any frame with sound volume larger than this will not be regarded as black frame
min_silence=10 ; Any deep silence longer than this amount of frames is a possible cutpoint
ticker_tape=0 ; Amount of pixels from bottom to ignore in all processing
max_repair_size=200

;### Punsih ###

punish=20 ; Compare to average for sum of 1=brightness, 2=uniform 4=volume, 8=silence, 16=schange, set to 0 to disable
punish_threshold=1.3 ; Multiply when amount is above average * punish_threshold
punish_modifier=2.0 ; When above average * threshold multiply score by this value


length_strict_modifier=1.1
length_nonstrict_modifier=1.5
combined_length_strict_modifier=2.0
combined_length_nonstrict_modifier=1.25
logo_present_modifier=1
excessive_length_modifier=0.01
ar_wrong_modifier=1.0
min_schange_modifier=0.5
max_schange_modifier=2.0
schange_threshold=80
cc_commercial_type_modifier=4.0
cc_wrong_type_modifier=2.1
cc_correct_type_modifier=0.75
dictionary_modifier=1.00


intelligent_brightness=0 ; Set to 1 to use a USA specific algorithm to tune some of the settings, not adviced outside the USA
give_up_logo_search=2000


;### Logo ###

logo_percentile=0.92 ; if more then this amount of logo is found then logo detection will be disabled
logo_threshold=0.50
aggressive_logo_rejection=1
connect_blocks_with_logo=1 ; set to 1 if you want successive blocks with logo on the transition to be regarded as connected, set to 0 to disable
cut_on_ar_change=1 ; set to 1 if you want to cut also on aspect ratio changes, set to 0 to disable
delete_show_after_last_commercial=1 ; set to 1 if you want to delete the last block if its a show and after a commercial
delete_show_before_first_commercial=1
delete_show_before_or_after_current=1 ; set to 1 if you want to delete the previous and the next show in the recording, this can lead to the deletion of trailers of next show
shrink_logo=5 ; Reduce the duration of the logo with this amount of seconds
after_logo=1 ; set to number of seconds after logo disappears comskip should start to search for silence to insert an additional cutpoint
before_logo=1 ;
reward=0
padding=0
ms_audio_delay=5
logo_max_percentage_of_screen=0.35
subtitles=0
delete_logo_file=1 ; set to 1 if you want comskip to tidy up after finishing


;### Output ###

output_framearray=1 ; create a big excel file for detailed analysis, set to 0 to disable
output_videoredo=1
output_womble=0
output_cuttermaran=0
output_mpeg2schnitt=0
output_mpgtx=0
output_zoomplayer_chapter=0
output_zoomplayer_cutlist=0
output_edl=0
output_vcf=0
output_btv=0 ; set to 1 if you want Beyond TV chapter cutlist output
output_projectx=0 ; set to 1 if you want ProjectX cutlist output (Xcl)
output_demux=0 ; set to 1 if you want comskip to demux the mpeg file while scanning
output_bsplayer=1
live_tv=1 ; set to 1 if you use parallelprocessing and need the output while recording
dictionary=0
cuttermaran_options="cut=\"true\" unattended=\"true\" muxResult=\"false\" snapToCutPoints=\"true\" closeApp=\"true\""
mpeg2schnitt_options="mpeg2schnitt.exe /S /E /R25 /Z %2 %1


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 

All times are UTC [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group