Switzerland & Germany
My ini works very well since years now. I use it with Kodi.
It's quite strict, but the number of "falso hits" is considerably low since newer comskip versions.
Thanks a lot to erik for this fabulous software!
Two important informations - what you might want to change:
- Intentionally did not use low resolution / high speed usage for the sake of accuracy
- Between 8 pm and 4 am it is switched to very low speed not to have too much impact on running recordings
Greetz from Switzerland - Chris
Code: Select all
detect_method=43 ;1=black frame, 2=logo, 4=scene change, 8=fuzzy logic, 16=closed captions, 32=aspect ration, 64=silence, 128=cutscenes, 255=all validate_silence=1 ; Default, set to 0 to force using this clues if selected above. validate_uniform=1 ; Default, set to 0 to force using this clues (like pure white frames) if blackframe is selected above. validate_scenechange=1 ; Default, set to 0 to force using this clues if selected above. verbose=0 ;show a lot of extra info, level 5 is also OK, set to 0 to disable max_brightness=60 ;frame not black if any pixels checked are greater than this (scale 0 to 255) test_brightness=40 ;frame not pure black if any pixels checked are greater than this, will check average brightness (scale 0 to 255) max_avg_brightness=25 ;maximum average brightness for a dim frame to be considered black (scale 0 to 255) 0 means autosetting max_commercialbreak=750 ;maximum length in seconds to consider a segment a commercial break min_commercialbreak=51 ;minimum length in seconds to consider a segment a commercial break max_commercial_size=125 ;maximum time in seconds for a single commercial or multiple commercials if no breaks in between min_commercial_size=4 ;mimimum time in seconds for a single commercial min_show_segment_length=250 ; any segment longer than this will be scored towards show. non_uniformity=500 ; Set to 0 to disable cutpoints based on uniform frames max_volume=500 ; any frame with sound volume larger than this will not be regarded as black frame min_silence=12 ; Any deep silence longer than this amount of frames is a possible cutpoint ticker_tape=0 ; Amount of pixels from bottom to ignore in all processing logo_at_bottom=0 ; Set to 1 to search only for logo at the lower half of the video, do not combine with subtitle setting punish=0 ; Compare to average for sum of 1=brightness, 2=uniform 4=volume, 8=silence, 16=schange, set to 0 to disable punish_threshold=1.3 ; Multiply when amount is above average * punish_threshold punish_modifier=2 ; When above average * threshold multiply score by this value intelligent_brightness=0 ; Set to 1 to use a USA specific algorithm to tune some of the settings, not adviced outside the USA logo_percentile=0.92 ; if more then this amount of logo is found then logo detection will be disabled logo_threshold=0.88 punish_no_logo=1 ; Default, set to 0 to avoid show segments without logo to be scored towards commercial aggressive_logo_rejection=0 connect_blocks_with_logo=1 ; set to 1 if you want successive blocks with logo on the transition to be regarded as connected, set to 0 to disable logo_filter=0 ; set the size of the filter to apply to bad logo detection, 4 seems to be a good value. delete_show_after_last_commercial=0 ; set to 1 if you want to delete the last block if its a show and after a commercial delete_show_before_or_after_current=1 ; set to 1 if you want to delete the previous and the next show in the recording, this can lead to the deletion of trailers of next show delete_block_after_commercial=0 ;set to max size of block in seconds to be discarded, set to 0 to disable remove_before=0 ; amount of seconds of show to be removed before ALL commercials remove_after=0 ; amount of seconds of show to be removed after ALL commercials shrink_logo=5 ; Reduce the duration of the logo with this amount of seconds after_logo=1 ; set to number of seconds after logo disappears comskip should start to search for silence to insert an additional cutpoint before_logo=1 ; set to number of seconds after logo appears comskip should start to search for silence to insert an additional cutpoint padding=0 ms_audio_delay=5 volume_slip=40 skip_b_frames=0 ; Set to 1 to force Comskip to skip frames for higher processing speed. max_repair_size=200 ; Will repair maximum 200 missing MPEG frames in the timeline, set to 0 to disable repairing for players that don't use PTS. disable_heuristics=4 bit pattern for disabling heuristics, adding 1 disables heristics 1, adding 2 disables heristics 2, adding 4 disables heristics 3, 255 disables all heuristics delete_logo_file=1 ; set to 1 if you want comskip to tidy up after finishing output_framearray=0 ; create a big excel file for detailed analysis, set to 0 to disable output_data=0 ; create a dump of the user data channel, used for CC and XDS (such as V-Chip info). Can be use together with output_framearray to remote debug CC decoding output_videoredo=0 output_womble=0 output_mls=0 ; set to 1 if you want MPeg Video Wizard bookmark file output output_cuttermaran=0 output_mpeg2schnitt=0 output_mpgtx=0 output_dvrcut=0 output_zoomplayer_chapter=0 output_zoomplayer_cutlist=0 output_edl=0 output_dvrmstb=0 ; Set to 1 if you're running DVRMS-Toolbox output_edlx=0 output_vcf=0 output_bsplayer=0 output_btv=0 ; set to 1 if you want Beyond TV chapter cutlist output output_projectx=0 ; set to 1 if you want ProjectX cutlist output (Xcl) output_avisynth=0 output_vdr=0 ; set to 1 if you want XBMC to skipping commercials output_demux=0 ; set to 1 if you want comskip to demux the mpeg file while scanning sage_framenumber_bug=0 sage_minute_bug=0 live_tv=0 ; set to 1 if you use parallelprocessing and need the output while recording live_tv_retries=4 ; change to 16 when using live_tv in BTV, used for mpeg PS and TS dvrms_live_tv_retries=300 ; only used for dvr_ms standoff=0 ; change to 8000000 when using live_tv in BTV cuttermaran_options="cut=\"true\" unattended=\"true\" muxResult=\"false\" snapToCutPoints=\"true\" closeApp=\"true\"" mpeg2schnitt_options="mpeg2schnitt.exe /S /E /R25 /Z %2 %1" avisynth_options="LoadPlugin(\"MPEG2Dec3.dll\") \nMPEG2Source(\"%s\")\n" dvrcut_options="dvrcut \"%s.dvr-ms\" \"%s_clean.dvr-ms\" " windowtitle="Comskip - %s" play_nice_start=2000 play_nice_end=0100 play_nice_sleep=5 added_recording=7 delete_show_before_first_commercial=2 output_default=1 output_plist_cutlist=0 edl_skip_field=3 delay_logo_search=0 lowres=10