running:
Linux Mint 18.0 | kernel 4.4.0-59
comskip 0.81.089
command used:
Code: Select all
comskip -u 102300 --ini=comskip_default.ini video.ts
Code: Select all
verbose=12
detect_method=69 ; 1=black frame, 2=logo, 4=scene change, 8=fuzzy logic, 16=closed captions, 32=aspect ratio, 64=silence, 128=cutscenes, 255=all
;==== GENERAL SETTINGS ====
intelligent_brightness=1 ; Set to 1 to use a USA specific algorithm to tune some of the settings, not adviced outside the USA
max_commercialbreak=250 ; maximum length in seconds to consider a segment a commercial break
min_commercialbreak=30 ; minimum length in seconds to consider a segment a commercial break
max_commercial_size=250 ; maximum time in seconds for a single commercial or multiple commercials if no breaks in between
min_commercial_size=4 ; mimimum time in seconds for a single commercial
min_show_segment_length=140 ; any segment longer than this will be scored towards show
padding=0
remove_before=0 ; amount of seconds of show to be removed before ALL commericals
remove_after=0 ; amount of seconds of show to be removed after ALL commercials
;ticker_tape=0 ; amount of pixels from bottom to ignore in all processing
;==== GLOBAL REMOVES ====
delete_show_before_first_commercial=0
min_commercial_break_at_start_or_end=25
;==== CPU LOAD REDUCTION ====
thread_count=2
hardware_decode=1
play_nice_start=-1
play_nice_end=-1
play_nice_sleep=2
;==== BLACK FRAME DETECTION SETTINGS ====
;test_brightness=40 ; frame not pure black if any pixels checked are greater than this, will check average brightness (scale 0 to 255)
;max_brightness=60 ; frame not black if any pixels checked are greater than this (scale 0 to 255)
min_black_frames_for_break=5
non_uniformity=500
;==== LOGO DETECTION SETTINGS ====
after_logo=0 ; number of seconds after logo disappears to create pseudo black frame
before_logo=0 ; number of seconds before logo appears to create pseudo black frame
connect_blocks_with_logo=0 ; set to 1 if you want successive blocks with logo on the transition to be regarded as connected, set to 0 to disable
delete_logo_file=1 ; set to 1 if you want comskip to tidy up after finishing
delay_logo_search=360 ; number of seconds to wait before logo search
logo_at_bottom=1 ; Set to 1 to search only for logo at the lower half of the video, do not combine with subtitle setting
;logo_filter=0 ; set the size of the filter to apply to bad logo detection, 4 seems to be a good value
logo_present_modifier=0.5
;logo_threshold=0.8250
punish_no_logo=0 ; Default, set to 0 to avoid show segments without logo to be scored towards commercial
shrink_logo=0 ; reduce the duration of the logo with this amount of seconds
two_pass_logo=1
use_existing_logo_file=0 ; use logo file in same directory if one exists
;==== SILENCE DETECTION SETTINGS ====
max_volume=0 ; any frame with sound volumen larger than this will not be regard as black frame
;min_silence=20 ; any deep silence longer than this amount of frames is a possible cutpoint
;==== CUTSCENE DETECTION SETTINGS ====
;cutscene_frame=0
;cutscene_dumpfile=""
;cutscene_threshold=10
;cutscene_file1="comskip_mytv.dmp"
;cutscene_file8=""
;==== OUTPUTS ====
output_edl=1
output_framearray=0 ; create a big excel file for detailed analysis, set to 0 to disable
output_vdr=0 ; set to 1 if you want XBMC to skip commercials
delete_logo_file=0